6540A REV K Norge Washer Parts List

Door catch kit (latch)

This door catch kit contains two door strikes and three door catches to service dryer doors that have one or two catches. Make sure to read the instructions to determine which one to use for your model. These parts keep the dryer door closed to allow the dryer to operate. If your door won't stay closed or will not start you may need to replace this part. This is a genuine OEM part.

Suspension spring

This suspension spring is used to support and balance the outer tub of your washer. If the spring is broken it will cause the washer to be off balance and noisy. Check your model to see how many springs are required for your model. The spring is sold individually.

Lower spray arm

Upper roller and axle - kit of 4 (roller and stud asm (4pk))

The upper roller and axle attach to the upper rack to allow the dishrack to move in and out along the track of the dishwasher. This is a kit includes 4 rollers and 4 axles for your upper rack. If your dish rack is not moving in and out of the dishwasher properly you may have a broken or missing wheel and it will need to be replaced. The rollers and axles are made out of plastic and are white in color. This is a genuine OEM kit.

Upper rack adjuster kit - white wheels, left and right sides (adjuster, arm assembly)

Dryer drum support roller (use wpl 8536974)

This drum support roller is sold individually. Most dryers require two. The tri-rings are included. This is a drum support roller for a dryer. It is a genuine replacement part. The part includes the drum roller only and does not include the tri-rings. This part is sold separately. Most dryers require two drum rollers. It is recommended to check and replace both drum support rollers at the same time to ensure proper drum rotation and because they often wear at the same rate. The drum support roller holds the drum in the proper position while it spins on the support wheels. If rollers are worn out, they will cause the dryer to be noisy.

Lower front dishrack wheel (front roller & stud)

This wheel is located on the front lower rack. It includes the axle. Sold individually.

Duct felt seal (trap duct felt)

The duct felt seal allows the front of the drum to glide smoothly on the exterior panel while the drum is rotating. The seal is located between the back of the drum and the rear dryer panel. If the heat is escaping from the drum area causing the dryer to run too long or if there are marks on your clothes you many need to replace the duct felt seal. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.

Light bulb - 40w 130v (lamp 1/2 size)

This 40 watt, 130-volt clear appliance light bulb is for your microwave. The light bulb is used on the inside of your microwave to provide light when the door is open or below the microwave to provide light for the cooking area. It is clear in color and has a small screw-in base. If your current bulb is burnt out or broken you will need to replace it. This bulb is a genuine OEM part and is sold individually.

Terminal block kit (use 5301167733)

This surface burner terminal block kit comes with interchangeable mounting brackets, ceramic wire nuts, heat shrink protective tubing and wires. This part is used to connect the wire harness to the surface burner element. If your element will not heat at all, or is not heating properly, it is likely an issue with the terminal block and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power supply before starting your repair.

Worm following gear (worm gear)

The follower gear works in conjunction with the worm gear and is part of the gear system that powers the mixer. If the mixer is making noises and not mixing you may need to replace this gear. This is a genuine OEM manufacturer-approved gear, used in stand mixers. Please remember to disconnect the power to the mixer before starting the repair.

Refrigerator center crisper drawer slide rail - white (support, center crisper drawer)

This is the center support rail for the crisper drawers. The rail attaches to the shelf frame between the two crisper drawers to provide support for the drawers as they slide in and out. The support rail is white in color and made of plastic. It measures approximately 13.5-inches in length and is a genuine OEM part.

Refrigerator crisper drawer (pan-crispr)

The crisper drawer with humidity control allows you to adjust the humidity within the crisper. By adjusting the humidity, it will extend the life of your produce. The crisper drawer is made of clear plastic, measures 13 1/2” wide and 18 1/2” deep. The drawer does not include the white trim on the front. This is a genuine OEM part and is sold individually.

Water inlet valve (valve-inlt)

This genuine replacement water inlet valve with tubing supplies water to the ice maker and water dispenser. The valve is 120 volts and 50/60 Hz. If your ice maker is not making ice or no water is coming from the dispenser, you may need to replace this part. The manufacturer has updated the water inlet valve and it no longer includes the removable pre-filter bracket. If you are unable to reuse the old removable pre-filter bracket, order part number WPW10445062. Please remember to disconnect the water and power supply before starting your repair.

Multi rib belt (sub 40111201)

This dryer drum belt has five ridges, 93-3/8 inches in length, and 3/8 of an inch wide. It is flat, black in color, and is made entirely of rubber. The belt helps rotate the drum. If the drum does not rotate and you can still hear the motor running, the belt may have broken and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to your dryer before starting the repair.